A deck built over living space is really two structures working together. On top, it needs to hold up to furniture, foot traffic, and weather. Underneath the surface, it must perform as a continuous waterproof shield for whatever lies below it. Ground-level patios can let rainwater soak harmlessly into the earth, but an elevated deck has no such margin for error. Even a pinhole gap in the waterproofing layer can send moisture into framing, drywall, or finished rooms over time. That's why every elevated deck needs a purpose-built waterproofing assembly, one engineered to move water toward drains and scuppers while maintaining an unbroken seal from edge to edge. That seal also has to hold up over years of real use: constant sun exposure, foot and furniture traffic, and the expansion and contraction that comes with seasonal temperature swings. Cornerstone Roofing Solutions builds and installs waterproofing systems throughout Derby, CO that are made to handle exactly these demands, season after season.
Waterproofing Systems We Offer
No two decks call for the same waterproofing approach. Structural layout, expected use, and the finished look you want all factor into which system makes the most sense. We walk through these variables with you before recommending a solution.
Liquid-Applied Elastomeric Systems
Fluid-applied coatings that cure into one continuous, flexible membrane covering the whole deck. Built up over several coats, these systems flex with the substrate and come in numerous finishes and colors. A strong fit for concrete, plywood, and lightweight concrete decking.
Roll-On Sheet Membrane Systems
Factory-made waterproofing sheets adhered directly to the deck substrate and finished with a protective wear layer on top. These membranes deliver consistent, uniform thickness and handle irregular deck shapes with numerous transitions or penetrations especially well.
Raised Pedestal Paver Systems
Tile or paver decking supported on height-adjustable pedestals sitting above a waterproofed base layer. Because the pavers lift out individually, the membrane underneath stays fully accessible for inspection and upkeep, all while presenting a clean, level finished surface.
Traffic-Grade Polyurethane Systems
Built for decks that see constant foot traffic, vehicles on parking structures, or contact with oils and chemicals. These heavy-duty polyurethane systems combine strong abrasion resistance with dependable waterproofing performance in demanding settings.
What Causes Deck Waterproofing to Fail
Knowing the typical ways deck waterproofing breaks down makes it easier to spot trouble early and design systems that avoid these problems from the outset.
Insufficient Slope to Drains
A deck without enough pitch toward its drainage points lets water sit and pond. Standing water places constant stress on the membrane, wearing it down fastest exactly where the pooling is deepest.
Wall Flashing Breakdown
The junction where a deck meets an adjoining wall is where most leaks start. Faulty flashing or worn sealant at this joint lets water slip behind the membrane and straight into the wall structure.
Cracking from Thermal Movement
Wide temperature swings cause the deck substrate to constantly expand and shrink. A coating without enough flexibility splits under that stress, opening direct routes for water to get in.
Wear Layer Breakdown
Steady foot traffic, moved furniture, and UV rays slowly wear down the surface coating over time. Once that protective layer thins out, the waterproofing beneath is left open to sun damage and impact.
Clogged and Overflowing Drains
When debris blocks a drain, water backs up and spills onto adjacent vertical surfaces, finding its way in at wall junctions or minor membrane flaws that wouldn't otherwise cause a problem.
Substandard Original Work
Skipped penetrations, membrane applied too thin, poor primer coverage, or a flood test that never happened are common root causes of early waterproofing failure requiring a full system tear-off and redo.
How We Install Deck Waterproofing
Structural and Drainage Review
We inspect the deck's substrate condition, current slope and drainage layout, drain sizing and placement, and the perimeter edge details. Structural issues, poor slope, or misplaced drains are flagged before any waterproofing begins.
Surface Preparation
We clean the deck thoroughly, strip out loose or damaged material, and fill and level any cracks or low spots in the substrate. Getting this stage right sets up everything that follows for long-term durability.
Primer Coat
We apply a primer matched to both the substrate and the waterproofing system selected, ensuring the membrane bonds fully and evenly. The right primer choice depends on the material below and the system going on top.
Reinforcing Critical Transitions
Before the field membrane goes down, we reinforce the highest-risk points, wall-to-deck joints, drain flanges, and penetrations, with extra membrane layers and proper flashing.
Full Membrane Application
The primary waterproofing membrane is applied across the entire deck at the correct thickness and coverage. For liquid systems, we build up multiple coats with proper cure time between each to form a complete, seamless barrier.
Wear Layer and Flood Test
A UV-resistant, traffic-rated wear layer goes on top of the fully cured membrane. Before we call the project finished, we flood-test the deck by holding standing water on the surface for a minimum of 24 hours to confirm the seal holds before any finish material is installed.